Q. WHY SHOULD THE GLASS TILES BE LAID OUT BEFORE FIXING TO WALL/FLOOR?
A. This is to ensure shade of glass is evenly distributed.

Q. HOW TO GET IT ON THE WALL?
A. Use Bright White Porcelain Thin Set

Q. SHOULD THE THIN SET DRY FIRST?
A. Read the instructions on the container.

Q. WHAT KIND OF GROUT SHOULD BE USED?
A. Sanded Grout is recommended since it does not shrink as much as some other grouts.  The grout color depends upon you and what you want the finished product to be.  White is preferred by most of the customers.

Q. WHAT SIZE TROWEL SHOULD BE USED?
A. Usually recommended is the 3/16” x 1/4” V-notch.

Q. WHAT STEPS SHOULD BE TAKEN TO APPLY SETTING MATERIAL?
A. Apply using these steps:

1. Using the flat side of a trowel to initiate the bond coat, firmly apply the setting material into the substrate (wall area).
2. With additional setting materials, comb horizontal, full notches in one direction to establish the proper depth of the setting bed.
3. Using the flat side of the trowel, flatten the notches to achieve a smooth, consistent setting bed approximately 1/8” thick.
4. Apply the sheets into the setting bed (mesh to the bonding material), using light even pressure to establish contact and eliminate any voids.
5. To achieve a uniform, flat surface tap lightly using a wooden beating block and a hammer.
6. Apply each sheet so that grout joints line up and a consistent field is maintained.  Prior to setting each sheet, check the setting bed for slight drying of the surface.  If drying occurs, remove setting bed and reapply.
7. To unify tile surface from one sheet to the next use a wooden beating block and hammer, again tapping lightly from one sheet to the next.
8. Straighten individual tiles prior to final set with the goal of creaking a consistent, overall field of mosaics. Pay particular attention to the joints between sheets to eliminate the sheet pattern.
   
9. Cure a minimum of 48 hours prior to cleaning.

Q. HOW DO I APPLY GROUT?
A. Apply using these steps:

1. Use only standard grade sanded grout mixed per instructions.  Apply grout with a rubber float, forcing grout into joints until full. (It is recommended to brush off the grout a little from bubble or pebble glass in order to show the beauty of the special shape.)

2. Do not level the grout with pebble glass or bubble glass so the shape of the pebble or bubble won’t be covered by grout. Use soft brush lower 1/3 of the grout while the grout still semi wet.
   
   
3. The grout will take longer to set.  For initial cleaning use clean, dry cheesecloths.  This method wicks additional moisture from the grout and avoids washing out the grout.
   
   
4. Allow grout to set up and smooth finish with a damp sponge.
   
   
5. For final polishing of excess grout haze use a clean, soft cloth.

Q. HOW DO I CUT THE GLASS?
A. It is recommended the glass not be cut.  The mesh backing can be cut and any glass that needs to be removed can be peeled off and put in a different spot to offset the lines of the square foot.

Q. HOW DO I KEEP THE PEBBLE GLASS FROM LOOKING BLOCKED?
A. Peel few pieces or so from the edge and move them over to make it appear as it is interlocked.

Q. WHERE CAN THE GLASS BE UTILIZED?
A. The glass can be utilized as:

1. Bathroom walls/floors
   1. understanding that when glass is wet, it can be slippery
   2. glass will break and shatter if hit with extreme force.  Neither glass nor ceramic tile should be installed where it will be subjected to these conditions.
2. Pools / Spas / various outdoor applications
3. Interior/Exterior of the building

Q. CAN GLASS TILES BE USED OUTSIDE?
A. Small tiles are very well suited for outdoors.  All tiles have a very high tolerance to freeze/thaw conditions, as they are nonporous.  They are also resistant to acid rain, ultra violet rays and chemicals.

Q. IS IT OK TO INSTALL OVER PLYWOOD?
A. Not recommended since plywood has a high degree of expansion and contraction.

Q. IS DRYWALL (SHEET ROCK, GREEN BOARD OR BLUE BOARD) AN ACCEPTABLE SETTING SURFACE IN DRY AREAS?
A. Yes, wire-reinforced mortar beds, cured 7 days prior to installation, and cementations board units for most applications are recommended.  For wall installations in interior DRY AREAS, drywall is widely accepted as a substrate, however a professional evaluation should be made to ensure that the installation would not be subjected to moisture.

Q. HOW LONG SHOULD CONCRETE CURE PRIOR TO INSTALLING GLASS TILES?
A. The industry minimum standard for concrete is 28 days.  For cold exterior and high moisture climates the cure times can extend to 60 days or more.

Q. HOW DO I WASH GLASS TILES?
A. Use a soft cloth and mild detergent and water, or an uncolored commercial window-cleaning product, such as Windex.

The above questions/answers are for informative use only.  See a reputable contractor for proper installation of our products.

Since Pacilantic is not an installer of glass and ceramic tiles, we suggest you contact a company that installs these products.

We hope you enjoy your new décor. 

Thank you for your business.